Flashing a new firmware by Browser What you need to flash You need the image file you want to flash. Image files have the extension *.nfi. You can't flash other images like *.img files. Don't try it - it won't work. You need either a DHCP server and a configured bootloader You need a browser and a network cable.

A guide on using FlashWizard Pro to flash, install, repair, modify the firmware on a Dreambox receiver. Dreambox Image Install With Flash. Exit Flashwizard and pull the power from you dreambox and wait for 30 seconds before reapplying power.

Connect your Dreambox to a switch/hub/router in your lokal LAN. To flash a new image, you can use the second stage loader. It must be present and not broken. The following steps assume you have a DHCP server. If you don't have one, you have to (klick) in the bootloader's serial setup. Yeh vaada raha wikipedia. - Power down the Dreambox, either using 'shutdown' and by switching off by the power switch.

Standby is not enough! - (1.) Press and hold the power button.

- (2.) Switch on your Dreambox. - (3.) Your Dreambox will get the next free DHCP IP address from your router. - Now, open a browser on your PC. (1.) enter in the address line '.

This is compatible with the following docking connector replacement boards: • SoundDock Original Dock Connector Type A standard replacement and will not upgrade SoundDock • USB Charge Upgrade and dock connector replacement Kit repair the fault as well as upgrading your SoundDock to charge iPod Touchs & iPhones up to 4th generation. Your SoundDock is a SoundDock Original Type A. Bose sounddock serial number lookup. • innexxis BC7 Bluetooth & Universal Charge Upgrade repair the fault as well as upgrading your SoundDock to both charge iPod Touchs & iPhones up to 4th generation as well as upgrading your SoundDock to Bluetooth allowing you to stream music wirelessly to it Please click the link below for the different SoundDock Original docking connectors.

- (2.) on the bottom of the page, there's a link called 'firmware upgrade'. - On the next page, you can select the flash image you want to flash. Be sure that it has the '.nfi' extension.

You can't flash other images (like.img)! - Click on 'FLASH!' It might take some time to upload and flash the image. - Switch the box off again, and on again. The new image should be flashed and working.

What you need to flash You need the image file you want to flash. Image files have the extension *.nfi. You can't flash other
images like *.img files. Don't try it - it won't work. You need either a DHCP server, a configured bootloader or a serial cable and a terminal program
like HyperTerm. You need a browser, and a network cable. If you connect the Dreambox directly to the PC,
you need a cross cable, if you connect trough a switch/hub/router you need a normal
(non-cross) cable.

To flash a new image, you can use the second stage loader. It must be present and not broken. The following steps assume you have a DHCP server. If you don't have one, you have to (klick) in the bootloader's serial setup. - Power down the Dreambox, either using 'shutdown' (to enter the deep-standby mode) or by using the power-switch.

Standby is not enough! (1.) Press and hold the lower frontpanel button. (2.) Switch on the dreambox, either by using the powerswitch or, in deep-standby mode, press the power button. Still, hold the lower button. (3.) A text '*** STOP ***' should appear. If something like '/flash'.

Appears, you didn't hold the right button. Now you can release the button. The bootloader entered the 'waiting' mode. (4.) Above the '*** STOP ***' text, there should appear an IP-address (four decimal values with a dot in between). If there appears the string 'dhcp' instead, the box still searches for a DHCP server. Wait a bit.

If it doesn't change, something doesn't work with the DHCP server. Check wether network cable is plugged in etc. If it just doesn't work, using the serial terminal - Now, open a browser on your PC. (1.) enter in the address line '(where ip must be replaced with the value in the LCD).

(2.) on the bottom of the page, there's a link called 'firmware upgrade'. - On the next page, you can select the flash image you want to flash. Be sure that it has the '.nfi' extension. You can't flash other images (like.img)!

- Click on 'FLASH!' It might take some time to upload and flash the image. - Switch the box off again, and on again.

The new image should be flashed and working.